EPS 16+ OS loads but no other disks (disk drive not ready)
EPS 16+ OS loads but no other disks (disk drive not ready)
Hi,
i installed a gotek/hxc drive and while the OS loads just fine i can´t seem to open any other image, most of the time it says "disk drive not ready" or if i wanna save something it says "disk drive changed".
I installed the basic provided Ensoniq Stuff into the root of the FAT formatted USB stick.
No idea what to do now, any help would be much appreciated, love this thing already
Thanks!
This getting weird, suddenly i was able to load a couple of the quickstart efe and also the Voder Demo when trying to load an EFE that worked before i get the "disk drive not ready" again.
Please help.
i installed a gotek/hxc drive and while the OS loads just fine i can´t seem to open any other image, most of the time it says "disk drive not ready" or if i wanna save something it says "disk drive changed".
I installed the basic provided Ensoniq Stuff into the root of the FAT formatted USB stick.
No idea what to do now, any help would be much appreciated, love this thing already
Thanks!
This getting weird, suddenly i was able to load a couple of the quickstart efe and also the Voder Demo when trying to load an EFE that worked before i get the "disk drive not ready" again.
Please help.
Re: EPS 16+ OS loads but no other disks (disk drive not ready)
You need a configuration which supports the proper disk change signal on pin 2.
Try this: http://www.mediafire.com/file/amczbxadz ... 9.CFG/file
Re: EPS 16+ OS loads but no other disks (disk drive not ready)
Which firmware version have you ? you may need to update it to the very last version.
Re: EPS 16+ OS loads but no other disks (disk drive not ready)
Hey, thanks for the feedback. Mondo1976,i downloaded the config file and now it kind of works,yay!
when i loaded the OS i have to load something from the OS Disk, for example a FX file, now i can load whatever file/disk i want and it works, even saving does work. Occasionally i get a "disk has been changed" message but basically it works.
is it supposed to work like this?
The Firmware is Version is 3.1a
Thanks!
when i loaded the OS i have to load something from the OS Disk, for example a FX file, now i can load whatever file/disk i want and it works, even saving does work. Occasionally i get a "disk has been changed" message but basically it works.
is it supposed to work like this?
The Firmware is Version is 3.1a
Thanks!
Re: EPS 16+ OS loads but no other disks (disk drive not ready)
Might as well update to "HxCFEUSB_V3_3_7_1a", but I suspect part of the issue is the pause/delay that the Gotek takes to put new disk selections into effect. When you use the Gotek up/down buttons, wait for a good 5 seconds before attempting to load something from the newly selected disk.
If that helps, you can lower the disk selection time down to 1 second so that the Gotek will "activate" the disk image that you have selected on the Gotek screen with less of a delay.
It's possible to get it working properly, as my EPS16 doesn't throw those kinds of errors. However, I have definitely seen that issue and it's a very common problem. For some reason, the Ensoniq EPS and EPS16 want some bizarro disk change setup that nothing else uses, and that makes it fussy unless you've got it dialed in perfectly.
Re: EPS 16+ OS loads but no other disks (disk drive not ready)
thanks man, sounds promising. where i can change this settings? the Config file just has a couple of weird signs in it
Re: EPS 16+ OS loads but no other disks (disk drive not ready)
Remove the USB stick and then you can hold down both the up & down buttons on the Gotek to enter the internal config menu. If you only have the normal 7-segment 3-digit Gotek display and not an OLED, you will have to refer to the readme that comes with the HxC firmware. It tells you which menu option is which, and how to see the Interface type (Generic Shugart), Family (Ensoniq), and --most relevant to what we're discussing-- the selection delay. *DO NOT* accidentally disable the selection delay if you don't have the third 'select' button option installed. Just lower it to 1 sec instead of its default of 4 seconds (or whatever it is on now).
The readme that I'm referring to is called "README_USAGE.TXT" and it's in the "Update_And_Usage_Documentation_README" folder of the Gotek firmware upgrade pack.
But... to make your life easier
Menu 0 - System family selection :
0F = Ensoniq
Menu 1 - Interface mode :
08 = GENERIC SHUGART DD
Menu 5 - Auto select delay :
01-08 : Delay (number of seconds) <---- CHANGE TO 1 SECOND AND NOT ZERO!!
Then Exit the config mode to save.
Re: EPS 16+ OS loads but no other disks (disk drive not ready)
Great, i´m going to give it a try. My Gotek has an OLED screen but only two buttons, i guess i would prefer a third button to actually select a disk to load but i´m just happy it works now.
thanks again for helping me out, this drive really adds a lot to this fantastic instrument.
thanks again for helping me out, this drive really adds a lot to this fantastic instrument.
Re: EPS 16+ OS loads but no other disks (disk drive not ready)
the current version is 3.3.7.1a. You should update your firmware first.
Re: EPS 16+ OS loads but no other disks (disk drive not ready)
Hi Jeff, tried to update but i get an [E01] which is assume is error one (one blink, one pause ...) which seems to be a non hxC flashed drive, which it is clearly not.
i have to say i bought it 2nd hand and already flashed.
i have to say i bought it 2nd hand and already flashed.
Re: EPS 16+ OS loads but no other disks (disk drive not ready)
Well... this explain everything... This EPS issue sounded odd to me...
You can get a true hxc firmware there : https://hxc2001.com/store/index.html
(This can be flashed with an usb stick, no need to open the machine. just contact me by email to have the files.)
Re: EPS 16+ OS loads but no other disks (disk drive not ready)
accidental doublepost
Last edited by DBK on Wed Jul 10, 2019 11:04 pm, edited 3 times in total.
Re: EPS 16+ OS loads but no other disks (disk drive not ready)
Thanks, Jeff. i wrote you am e-mail. I really thought i bought it Ensoniq ready and HcX flashed.
Re: EPS 16+ OS loads but no other disks (disk drive not ready)
Alright, turns out i haven´t had a HxC flashed floppy Emulator. Jeff was kind enough to support me anyway and i ended up with a working and flashed drive, that´s quite something! I´ll happily buy the HxC Software.
Thanks, Jeff!
Thanks, Jeff!