Problem with OLED and Gotek
Problem with OLED and Gotek
Hi, I correctly installed an OLED in my Gotek using latest HxC firmware.
The ONLY way the display will work is just after initiating the upgrade process (on + hold both buttons) and then everything works fine, I can see the image files, select through them and even go in settings in the OLED. Resets work fine too.
The issue is when I turn off the Amiga and back on again the Gotek will work BUT the OLED will not work at all unless I initiate the update again.
What is wrong ?
The ONLY way the display will work is just after initiating the upgrade process (on + hold both buttons) and then everything works fine, I can see the image files, select through them and even go in settings in the OLED. Resets work fine too.
The issue is when I turn off the Amiga and back on again the Gotek will work BUT the OLED will not work at all unless I initiate the update again.
What is wrong ?
Re: Problem with OLED and Gotek
This is an issue with the screen reset signal. The R-C circuit of this screen is probably too slow.
Can you send me a picture of this OLED screen (pcb side) ?
I will add a latency setting in the firmware to deal with these slow screens, probably late in the afternoon.
Can you send me a picture of this OLED screen (pcb side) ?
I will add a latency setting in the firmware to deal with these slow screens, probably late in the afternoon.
Re: Problem with OLED and Gotek
There you go
- Attachments
-
- Webp.net-compress-image.jpg (110.53 KiB) Viewed 10995 times
Re: Problem with OLED and Gotek
If I hit the reset jumper on the Gotek board the OLED switches on
https://www.youtube.com/watch?v=LDP2heuzSG4
https://www.youtube.com/watch?v=LDP2heuzSG4
Re: Problem with OLED and Gotek
If you want to try the power up delay feature :dougal wrote: ↑Tue Nov 28, 2017 1:20 pm If I hit the reset jumper on the Gotek board the OLED switches on
https://www.youtube.com/watch?v=LDP2heuzSG4
https://hxc2001.com/vrac/HxCUSBFE.UPD
Update the firmware, once done remove the usb stick and press both buttons to enter the setting menu.
you should find an "Power up delay" entry. Enter it and select "1s" for a first try.
then exit the main menu.
After you can power cycle the amiga and let me know if the screen init is ok at power up.
By default menu items are automatically selected after 4 seconds. No need to add the select button.
please keep in mind that this firmware is a "work in progress" firmware and have probably lots of regressions since i have done important changes. So you may have others issues since i haven't tested it on Amiga yet .
Re: Problem with OLED and Gotek
Sorry there is not that option - The FW is v3.0.33.12a
There was AUTOSELECT which was 4s which I changed to 1s but it didnt make a difference to the OLED
There was AUTOSELECT which was 4s which I changed to 1s but it didnt make a difference to the OLED
Re: Problem with OLED and Gotek
This link :
https://hxc2001.com/vrac/HxCUSBFE.UPD
is the v3.0.34.3a firmware.
Please update to it and try what i said in my previous post.
Update procedure : https://hxc2001.com/docs/gotek-floppy-e ... pdate.html
Re: Problem with OLED and Gotek
Hi thanks I did that it updated and showed the option - Power Delay was NONE but that did not work, so I tried 1 SEC as you said and it still did not workJeff wrote: ↑Tue Nov 28, 2017 2:04 pmThis link :
https://hxc2001.com/vrac/HxCUSBFE.UPD
is the v3.0.34.3a firmware.
Please update to it and try what i said in my previous post.
Update procedure : https://hxc2001.com/docs/gotek-floppy-e ... pdate.html
Re: Problem with OLED and Gotek
That link is taking me to the hxc2001 homepageJeff wrote: ↑Tue Nov 28, 2017 2:56 pm Ok and with this one ? :
https://hxc2001.com/vrac/HxCUSBFE.UPD
(v3.0.34.4a)
Re: Problem with OLED and Gotek
Sorry.dougal wrote: ↑Tue Nov 28, 2017 3:01 pmThat link is taking me to the hxc2001 homepageJeff wrote: ↑Tue Nov 28, 2017 2:56 pm Ok and with this one ? :
https://hxc2001.com/vrac/HxCUSBFE.UPD
(v3.0.34.4a)
This one :
https://hxc2001.com/vrac/HxCUSBFE2.UPD
(v3.0.34.4a)
Re: Problem with OLED and Gotek
Sorry but still not working
Re: Problem with OLED and Gotek
ok will check this this evening. Can you check that your setting still saved after a reset ?
about the screen did you know if your model have the pull resistors on the i2c lines ?
Re: Problem with OLED and Gotek
Yes it saves the settings even after reset. Just to let you know the new fw's you made have other issues, the last one you sent me autoboot.hfe works but the other disk images do not and the one before not even autoboot.hfe loads. The other fw's 3.0.33.12a which are in the file section as normal load autoboot and disk images fine
I dont know about pull resistors
Re: Problem with OLED and Gotek
For the other issues i know, this is normal.