Emulate NEC FD1138D for embroidery machine

Post Reply
VortexH98
Posts: 5
Joined: Wed Aug 26, 2020 5:33 am

Emulate NEC FD1138D for embroidery machine

Post by VortexH98 »

Hi, I'm new to the forum, this firmware can emulate an FD1138D for an embroidery machine that uses the ZSK or Tajima .dst format

Jeff
Site Admin
Posts: 8091
Joined: Fri Oct 20, 2006 12:12 am
Location: Paris
Contact:

Re: Emulate NEC FD1138D for embroidery machine

Post by Jeff »

VortexH98 wrote:
Wed Aug 26, 2020 5:38 am
Hi, I'm new to the forum, this firmware can emulate an FD1138D for an embroidery machine that uses the ZSK or Tajima .dst format
Hi,

Sure it can. It was already tested with the ZSK and Tajima machines.

VortexH98
Posts: 5
Joined: Wed Aug 26, 2020 5:33 am

Re: Emulate NEC FD1138D for embroidery machine

Post by VortexH98 »

Thank you very much for your answer Jeef.
Tomorrow I get the USB ttl, and I will also buy the firmware, but I have some doubts after having read the instructions.
I understood the first process First time bootloader Flashing / Programming process. after that I didn't really understand the firmware update process.
What Firmware should I use to emulate the FD1138D, and also if I only have to connect the USB with the file corresponding to the connected equipment.
Attachments
ACM330.jpeg
ACM330.jpeg (56.54 KiB) Viewed 2046 times
FD1138D.jpeg
FD1138D.jpeg (52.8 KiB) Viewed 2046 times
1.jpeg
1.jpeg (54.05 KiB) Viewed 2046 times

Jeff
Site Admin
Posts: 8091
Joined: Fri Oct 20, 2006 12:12 am
Location: Paris
Contact:

Re: Emulate NEC FD1138D for embroidery machine

Post by Jeff »

Once you have flashed the bootloader, just install/update the normal firmware present into this archive :

https://hxc2001.com/download/floppy_dri ... rmware.zip

Set the jumper to S0.

VortexH98
Posts: 5
Joined: Wed Aug 26, 2020 5:33 am

Re: Emulate NEC FD1138D for embroidery machine

Post by VortexH98 »

I already acquired everything I need, at the moment of flashing it gives me this error.
Attachments
puerto.png
puerto.png (10.54 KiB) Viewed 2028 times

VortexH98
Posts: 5
Joined: Wed Aug 26, 2020 5:33 am

Re: Emulate NEC FD1138D for embroidery machine

Post by VortexH98 »

I switched to windows 7 and it worked without any problem.
I already installed the firmware (* .upd). I will continue with the following steps.

VortexH98
Posts: 5
Joined: Wed Aug 26, 2020 5:33 am

Re: Emulate NEC FD1138D for embroidery machine

Post by VortexH98 »

I am using indexed mode.
I followed the steps in the foulder_mount folder, but in the emulator it displays the following Err message followed by a 000. And it does not transfer the design to the embroidery machine. Surely I am doing something wrong.

Jeff
Site Admin
Posts: 8091
Joined: Fri Oct 20, 2006 12:12 am
Location: Paris
Contact:

Re: Emulate NEC FD1138D for embroidery machine

Post by Jeff »

VortexH98 wrote:
Sat Aug 29, 2020 12:10 am
I am using indexed mode.
I followed the steps in the foulder_mount folder, but in the emulator it displays the following Err message followed by a 000. And it does not transfer the design to the embroidery machine. Surely I am doing something wrong.
Have you some files images on the stick ?

Is the machine supporting DOS/FAT file system ?

Post Reply