OLED mod

Post Reply
aotta
Posts: 36
Joined: Thu Apr 13, 2017 10:39 am

Re: OLED mod

Post by aotta »

Kingstener wrote:ooh, it looks strange... :shock:

- 0.91" OLED 128x32 with SSD1306 driver ?
- Fuses from readme?
- R/C on reset 1000nF/27K? (if it is a SPI display)
- VCC 3,3V ?

Swap of SCL / SDA brings nothing to fry :wink:
Thank you for the help!
i ordered 128x32 OLED... i am not sure the chinese store send me a 128x64 instead...
fuses ok, i2c one, but.... i used 5v for VCC, since i swapped for testing the OLED with the LCD display!!!
May be it's the overvoltage had fried the oled... :roll:

Kingstener
Posts: 67
Joined: Sat Mar 04, 2017 1:47 pm

Re: OLED mod

Post by Kingstener »

No, this also works at 5V, but it can be the reset does not work properly.
The resolution should be printed on the display
Attachments
Unbenannt.jpg
Unbenannt.jpg (79.14 KiB) Viewed 6651 times

aotta
Posts: 36
Joined: Thu Apr 13, 2017 10:39 am

Re: OLED mod

Post by aotta »

Kingstener wrote:No, this also works at 5V, but it can be the reset does not work properly.
The resolution should be printed on the display
In the I2C one's is only printed 0,91 oled... :(
I tried with 3,3v, with no change... but it's probably too late, and display is gone.
I'm waiting for a new one, arriving in a few days. Thank again for your support!

af0l
Posts: 10
Joined: Sun Mar 27, 2016 12:46 pm

Re: OLED mod

Post by af0l »

You can always verify the display using a Raspberry PI or similar... I find it very hard to believe that it would go out like that.

Kingstener
Posts: 67
Joined: Sat Mar 04, 2017 1:47 pm

Re: OLED mod

Post by Kingstener »

I guess at 0.91" is the a maximum resolution 128x32 pixel

aotta
Posts: 36
Joined: Thu Apr 13, 2017 10:39 am

Re: OLED mod

Post by aotta »

Kingstener wrote:I guess at 0.91" is the a maximum resolution 128x32 pixel
no, you're in error... i've found on amazon, ebay and aliexpress more 128x64 oled than 128x32, and the price are even lower!
Edit: sorry, you are right.. The 128x64 are 0.96 inch sized

Kingstener
Posts: 67
Joined: Sat Mar 04, 2017 1:47 pm

Re: OLED mod

Post by Kingstener »

Ooh, interesting, can you please give me a link?

aotta
Posts: 36
Joined: Thu Apr 13, 2017 10:39 am

Re: OLED mod

Post by aotta »

Kingstener wrote:Ooh, interesting, can you please give me a link?
sorry, as corrected in previous post, i confused 0.96 inch with 0.91 ones.. :(

aotta
Posts: 36
Joined: Thu Apr 13, 2017 10:39 am

Re: OLED mod

Post by aotta »

solved...
the display was fried... arrived new oled and now all ok!
thank Kingstener for the patience! :)
BBC3000.jpg
BBC3000.jpg (82.24 KiB) Viewed 6590 times

Kingstener
Posts: 67
Joined: Sat Mar 04, 2017 1:47 pm

Re: OLED mod

Post by Kingstener »

In the link of first post I've added an easy experimentally way to make it with a Digispark - it's only in german, but there are some pictures and I believe that should be enough for DIY... :wink:



@aotta looks nice... :D

aotta
Posts: 36
Joined: Thu Apr 13, 2017 10:39 am

Re: OLED mod

Post by aotta »

Kingstener wrote:In the link of first post I've added an easy experimentally way to make it with a Digispark - it's only in german, but there are some pictures and I believe that should be enough for DIY... :wink:
A solderless oled mod with a Digispark? Great!!!
...now that arrived the pcb and the smd components for another hxc... :cry: :lol:

Kingstener
Posts: 67
Joined: Sat Mar 04, 2017 1:47 pm

Re: OLED mod

Post by Kingstener »

Projekt no longer available due to incompatibility with newer HxC-Firmware >v3.0.19.2a

The redesigned and optimized low level I2C & LCD control from v3.0.20.1a upward works not longer properly with the OLED firmware - I'm sorry, but maybe the time will bring new ideas, good luck...

Jeff
Site Admin
Posts: 8092
Joined: Fri Oct 20, 2006 12:12 am
Location: Paris
Contact:

Re: OLED mod

Post by Jeff »

This is fixed with the last version i sent to you this afternoon. Tested and confirmed by another user.

Someone i have a backup of the document ? I will upload it somewhere.

Kingstener
Posts: 67
Joined: Sat Mar 04, 2017 1:47 pm

Re: OLED mod

Post by Kingstener »

Jeff wrote: This is fixed with the last version i sent to you this afternoon. Tested and confirmed by another user.
Please stay with reality! My decision is based on the state of the software at http://torlus.com/floppy/forum/viewtopi ... 043#p16037 and that did not work stable again :(
Jeff wrote: Someone i have a backup of the document ? I will upload it somewhere.
Heyhey....
Just as it was your decision to take money for your idea, it is my decision to stop the spread of my idea as long as this is not proper works with your new firmware
I think that you have to respect this - or do I somewhere push a upload from a copy of your bootloader? :x

If it is tolerable again and it is stable, maybe I will release the project again...

Jeff
Site Admin
Posts: 8092
Joined: Fri Oct 20, 2006 12:12 am
Location: Paris
Contact:

Re: OLED mod

Post by Jeff »

No problem but this means that i will have to add the direct support into the firmware.
For your interest this is now stable with the 3.0.21.5a :
http://torlus.com/floppy/forum/viewtopi ... =60#p16043

Post Reply