- gotek connection.jpg (201.4 KiB) Viewed 5448 times
Korg T3 data error
Re: Korg T3 data error
Seems fine.
Try this : start the software, open the serial port, connect.
If after some seconds the gotek is not detected try to make a contact between GND and RST to reset the gotek. wait again some seconds.
Try this : start the software, open the serial port, connect.
If after some seconds the gotek is not detected try to make a contact between GND and RST to reset the gotek. wait again some seconds.
-
- Posts: 18
- Joined: Mon Jan 08, 2018 7:12 pm
Re: Korg T3 data error
Shall I disconnect the power before and the tx and rx cables?
Re: Korg T3 data error
No no, do the reset procedure while all is up and connected.monolight77 wrote: ↑Thu Mar 01, 2018 2:26 amShall I disconnect the power before and the tx and rx cables?
don't make a permanent connection between GND and RST. One second is enough.
btw what is displayed in the "TX" & "RX" fields in the flasher software ?
-
- Posts: 18
- Joined: Mon Jan 08, 2018 7:12 pm
Re: Korg T3 data error
tx moves from 0 to 10
rx is always 0
I have discover a blown up voltage regulator in the Gotek. Maybe I made a bad power connection at same point. I will change it and come back.
Thanks!
rx is always 0
I have discover a blown up voltage regulator in the Gotek. Maybe I made a bad power connection at same point. I will change it and come back.
Thanks!
-
- Posts: 18
- Joined: Mon Jan 08, 2018 7:12 pm
Re: Korg T3 data error
Good morning Jeff,
Back again! Wish you could help me....
Gotek connected to computer, not receiving instructions from the hxc soft.
Resetting (gnd/reset shortcut) makes no difference.
When connected to my Korg T3 it acts normally. Recognises pen drive and makes the partitions.
Only thing is trying with another computer but I only have W10 in all!!
Can I install the soft and enter my password in several computers to try? Or this is going to be block by your server?
Thanks!
Back again! Wish you could help me....
Gotek connected to computer, not receiving instructions from the hxc soft.
Resetting (gnd/reset shortcut) makes no difference.
When connected to my Korg T3 it acts normally. Recognises pen drive and makes the partitions.
Only thing is trying with another computer but I only have W10 in all!!
Can I install the soft and enter my password in several computers to try? Or this is going to be block by your server?
Thanks!
- Attachments
-
- 20180309_105143-580x1031.jpg (159.86 KiB) Viewed 5406 times
-
- 20180309_105143-580x1031.jpg (159.86 KiB) Viewed 5406 times
-
- 20180309_100842-580x1031.jpg (168.51 KiB) Viewed 5406 times
Re: Korg T3 data error
no, no problem you can.monolight77 wrote: ↑Fri Mar 09, 2018 12:05 pm
Can I install the soft and enter my password in several computers to try? Or this is going to be block by your server?
Btw the last picture is interesting : in flashing mode the screen should be off. Are you sure that the BOOT0 strap is correctly soldered ?
if rx is always 0 then there is a problem : the gotek don't answer - check the boot0 strap and the connections. You can also do a loopback test to check your usb adapter : connect the rx and tx signal together without the gotek. if tx and rx increase together then this is ok.
-
- Posts: 18
- Joined: Mon Jan 08, 2018 7:12 pm
Re: Korg T3 data error
If I connect the Gotek to the serial and then to the computer, the display is black.
If I connect it without the BOOT0-VCC3V3 strap it lights. After this I put the jumper: that is why in the pics the display shows 000.
I have double check my soldering of the BOOT0-VCC3V3 stripes and is ok.
If I connect only the serial adapter to the PC, start HxC utility, open COM1, make a shortcut between the serial rx and tx and hit "connect" , tx varies but rx not.
If I connect it without the BOOT0-VCC3V3 strap it lights. After this I put the jumper: that is why in the pics the display shows 000.
I have double check my soldering of the BOOT0-VCC3V3 stripes and is ok.
If I connect only the serial adapter to the PC, start HxC utility, open COM1, make a shortcut between the serial rx and tx and hit "connect" , tx varies but rx not.
Re: Korg T3 data error
no, you need to put the jumper before powering up the gotek.monolight77 wrote: ↑Fri Mar 09, 2018 1:33 pmIf I connect the Gotek to the serial and then to the computer, the display is black.
If I connect it without the BOOT0-VCC3V3 strap it lights. After this I put the jumper: that is why in the pics the display shows 000.
This is not good at all. you need to "fix" this. Are you opening the right com port ?monolight77 wrote: ↑Fri Mar 09, 2018 1:33 pmIf I connect only the serial adapter to the PC, start HxC utility, open COM1, make a shortcut between the serial rx and tx and hit "connect" , tx varies but rx not.
-
- Posts: 18
- Joined: Mon Jan 08, 2018 7:12 pm
Re: Korg T3 data error
I will try to fix the com/serial issue.
Thanks Jeff!
Your help is invaluable!
Thanks Jeff!
Your help is invaluable!
-
- Posts: 18
- Joined: Mon Jan 08, 2018 7:12 pm
Re: Korg T3 data error
Done!
My Gotek is flashed with HxC firm and installed in my KORG T3.
Whn I switch on it reads "Ldr".
Now trying to make it work...
Thanks Jeff!!!
My Gotek is flashed with HxC firm and installed in my KORG T3.
Whn I switch on it reads "Ldr".
Now trying to make it work...
Thanks Jeff!!!
Re: Korg T3 data error
Well done ! Now just copy the latest firmware upd file to the root of the usb stick.monolight77 wrote: ↑Fri Mar 09, 2018 6:40 pmDone!
My Gotek is flashed with HxC firm and installed in my KORG T3.
Whn I switch on it reads "Ldr".
Now trying to make it work...
Thanks Jeff!!!
-
- Posts: 18
- Joined: Mon Jan 08, 2018 7:12 pm
Re: Korg T3 data error
Hello again, wish some body could help...
My Gotek is installed at the Korg T3 EX and I can see any hfe available.
Now, when I transfer via SMF any sample from Sound Forge to the T3 I can play with it and include it in any patch, but when the time of saving to the Gotek comes the T3 displays "ERROR: Disk Type Error". This can happen because the T3 has two different format possibilities: 1) PRO/COMBI/SEQ 4 Files and 2) PCM/PROG/COMBI/SEQ.
It seems that every hfe file I have is of the 1) type... is there someone who can provide the 2) type?
Thank you very much!
My Gotek is installed at the Korg T3 EX and I can see any hfe available.
Now, when I transfer via SMF any sample from Sound Forge to the T3 I can play with it and include it in any patch, but when the time of saving to the Gotek comes the T3 displays "ERROR: Disk Type Error". This can happen because the T3 has two different format possibilities: 1) PRO/COMBI/SEQ 4 Files and 2) PCM/PROG/COMBI/SEQ.
It seems that every hfe file I have is of the 1) type... is there someone who can provide the 2) type?
Thank you very much!
Re: Korg T3 data error
You can't format an image using this type ?monolight77 wrote: ↑Sun Mar 25, 2018 9:27 pmHello again, wish some body could help...
My Gotek is installed at the Korg T3 EX and I can see any hfe available.
Now, when I transfer via SMF any sample from Sound Forge to the T3 I can play with it and include it in any patch, but when the time of saving to the Gotek comes the T3 displays "ERROR: Disk Type Error". This can happen because the T3 has two different format possibilities: 1) PRO/COMBI/SEQ 4 Files and 2) PCM/PROG/COMBI/SEQ.
It seems that every hfe file I have is of the 1) type... is there someone who can provide the 2) type?
Thank you very much!
-
- Posts: 18
- Joined: Mon Jan 08, 2018 7:12 pm
Re: Korg T3 data error
I have just seen your mail. I will try with those files.
Thank you very much Jeff!
Thank you very much Jeff!