Gotek and i2c lcd display ?????
Gotek and i2c lcd display ?????
Hi,
i have connected an i2c lcd display to an gotek usb floppy emulator.
Flashed newest Firmware USB HxCFloppyEmulator v3.0.3.1a.
I have connected 5v, ground on the programming connector on gotek
Also i have connected sda, scl with 4.7k ohms resistors on jumper j7 on gotek.
So the display goes on and nothing else happens.
I have tested without resistors with the same result.
Does the gotek emulator functions with i2c lcd display as mentioned in the firmware release notes txt ?????
Best regards
i have connected an i2c lcd display to an gotek usb floppy emulator.
Flashed newest Firmware USB HxCFloppyEmulator v3.0.3.1a.
I have connected 5v, ground on the programming connector on gotek
Also i have connected sda, scl with 4.7k ohms resistors on jumper j7 on gotek.
So the display goes on and nothing else happens.
I have tested without resistors with the same result.
Does the gotek emulator functions with i2c lcd display as mentioned in the firmware release notes txt ?????
Best regards
Re: Gotek and i2c lcd display ?????
Please note that 2 additionnals 4.7Kohms pull up resistors (+5V) are needed on SCL & SDA.
So pull up +5v means: one end of 4.7k resistor to 5v and the other end to scl & sda connections ????
Is that right ???
I also have tested this but the same result: display goes on and no output ????????????
Any help appreciated ?????
I have taken this display:
http://www.amazon.de/gp/product/B00855Z ... ge_o00_s00
i think its the same as in the txt mentioned.
So pull up +5v means: one end of 4.7k resistor to 5v and the other end to scl & sda connections ????
Is that right ???
I also have tested this but the same result: display goes on and no output ????????????
Any help appreciated ?????
I have taken this display:
http://www.amazon.de/gp/product/B00855Z ... ge_o00_s00
i think its the same as in the txt mentioned.
Re: Gotek and i2c lcd display ?????
Update:
With the help of jeff the sainsmart lcd display works fine.
An modified gotek firmware is needed to communicate with such display.
Thank you very much
Best regards
With the help of jeff the sainsmart lcd display works fine.
An modified gotek firmware is needed to communicate with such display.
Thank you very much
Best regards
Re: Gotek and i2c lcd display ?????
Solved by email. New version incoming.
Re: Gotek and i2c lcd display ?????
lupo2110
Did you still use the pull up resistors?
I have a similar display but get the top line all switched on and the lower is all off.
This is my LCD
http://www.ebay.com/itm/321558542340?_t ... EBIDX%3AIT
It is similar to yours as it uses the same PCF8574T
Did you still use the pull up resistors?
I have a similar display but get the top line all switched on and the lower is all off.
This is my LCD
http://www.ebay.com/itm/321558542340?_t ... EBIDX%3AIT
It is similar to yours as it uses the same PCF8574T
Re: Gotek and i2c lcd display ?????
Yes pull up resistors have to be installed but this is needed to enhance the signal quality in the sda and scl lines.
Perhaps your display has a defect ?!
Perhaps your display has a defect ?!
Re: Gotek and i2c lcd display ?????
Thanks for the help
Works perfect with version 3.0.4.0a
Works perfect with version 3.0.4.0a
Re: Gotek and i2c lcd display ?????
Hi Jeff! i have a I2C board + LCD display how to connect the wire?
Connected VCC and GND on the programming connector
SDA and SCL on the J7 position
But when turn on amiga display do not appear characters,see photo.
http://i742.photobucket.com/albums/xx61 ... g~original
Connected VCC and GND on the programming connector
SDA and SCL on the J7 position
But when turn on amiga display do not appear characters,see photo.
http://i742.photobucket.com/albums/xx61 ... g~original
Re: Gotek and i2c lcd display ?????
Any news for my problem?danko wrote:Hi Jeff! i have a I2C board + LCD display how to connect the wire?
Connected VCC and GND on the programming connector
SDA and SCL on the J7 position
But when turn on amiga display do not appear characters,see photo.
http://i742.photobucket.com/albums/xx61 ... g~original
Re: Gotek and i2c lcd display ?????
Am i supposed to have news about this ?
I don't see the pull resistors on your picture and i don't see which I2C module you are using too, so i have no news since i don't have enough information to make any answers. So please make more pictures
I don't see the pull resistors on your picture and i don't see which I2C module you are using too, so i have no news since i don't have enough information to make any answers. So please make more pictures
Re: Gotek and i2c lcd display ?????
Since I am no expert I am using such layout on a Stripboard for connecting the display:
It is working fine, but is it also right?
It is working fine, but is it also right?
Re: Gotek and i2c lcd display ?????
if the read wires is the resistors, yes this is correct.xadox wrote:Since I am no expert I am using such layout on a Stripboard for connecting the display:
It is working fine, but is it also right?