Problem floppy emualator for CNC machine

[seaman_2007]

Session 1

[seaman_2007]

Session 2

[seaman_2007]

Session 3

[Jeff]

Send foto problem, "The file is too big, maximum allowed size is 256 KiB."
Where i can upload photos and videos?

i send to you an email with an ftp server address to put all you want!

[Jeff]

Send foto problem, "The file is too big, maximum allowed size is 256 KiB."
Where i can upload photos and videos?

i send to you an email with an ftp server address to put all you want!

Ok i got your videos ! Very impressive ! Thanks !

The loading seems slow ! I think that this is a GAP3 setting problem.
That's why i have corrected this setting with these files images.
Tell me if the loading speed up!

[seaman_2007]

We on the contrary, sought a low speed, then the data is transferred without errors. In the "floppy emulator setting " indicated "IBM PC 720 kb ". In all other modes to read faster and get error in knitting porgram.

[seaman_2007]

Hi Jeff!
How are you?
Hope you are fine and well.
I have a problem.
The old computer at which was installed the HxC floppy emulator, has been replaced by more modern
After replacing the computer I could not write data to a floppy disk emulator installed on new computer but all worked on the old computer correctly
Differences from the old computer and new computer is:
1) support only a single floppy (A).
2) higher productivity.
3) Additional Information:
version of the firmware emulator «V1_6_1_1B»;
emulator connected via a twisted cable; ( A mode )
in the bios of the the computer floppy listed as 5.25 1.2 m; (A mode )
Jumper is setting in the following way



PS:
with a real, floppy 5 "25 disk driver everything is working properly
waiting for your advice
with best regards
Slava

[Jeff]

Hi Jeff!
How are you?
Hope you are fine and well.
I have a problem.
The old computer at which was installed the HxC floppy emulator, has been replaced by more modern
After replacing the computer I could not write data to a floppy disk emulator installed on new computer but all worked on the old computer correctly
Differences from the old computer and new computer is:
1) support only a single floppy (A).
2) higher productivity.
3) Additional Information:
version of the firmware emulator «V1_6_1_1B»;
emulator connected via a twisted cable; ( A mode )
in the bios of the the computer floppy listed as 5.25 1.2 m; (A mode )
Jumper is setting in the following way



PS:
with a real, floppy 5 "25 disk driver everything is working properly
waiting for your advice
with best regards
Slava

Can you access the floppy emulator with this new PC ? (can you read the disk?)
Did you see something special on the HxC LCD when you try write on the HxC ?

Note: There are a new software for Windows :
https://hxc2001.com/floppy_drive_emulat ... fd_hxc.zip
With this one you should be able to avoid the use of the HxC Floppy Emulator on the modern/windows machine.
Can you send me your software ? I want to check if this one can work on the VFD virtual drive.

[seaman_2007]

I moved to the sd-card pre-prepared image (located in the attached file), working from the command line under real DOS, OS was not able to access the floppy A:, the system turned to HxC floppy emulator (on the LCD message was RA).
I did check, transferred to the card images of floppy disks 3,5 '1,44 M and 5.25 M 1.2, OS appealed to the HxC Floppy emulatoru no errors!
Unfortunately CNC machine can only work with a floppy drive 5.25 ".
Configuration of jumpers in the A:/ twisted cable.
. . . .
. |. .
. . |.
I want to emphasize that earlier this image worked on the old machine with no problems.
The difference was previously installed as drive B :/ on a direct cable, configuration jumpers
. . . .
. . |.
. |. .

«Vfd_hxc» I can not use because the program runs under pure DOS.
It makes no sense to send you the program because it requires a hardware dongle (hardlock).

Waiting for your advice.

[Jeff]

I did check, transferred to the card images of floppy disks 3,5 '1,44 M and 5.25 M 1.2, OS appealed to the HxC Floppy emulatoru no errors!
Unfortunately CNC machine can only work with a floppy drive 5.25 ".

So you can read 1.44MB disk image with the HxC on this new PC ?
In this case this probably an double or single step issue. (Bios issue in fact...)
Try the attached disk image on the pc.

empty_singlestep.zip

(10.11 KiB) Downloaded 466 times

[koh81]

Hello I'm using the USB floppy emulator, there is a way that i can configure the Floppy emulator similar to the parameters that worked with the SD emulator?

[Jeff]

Hello I'm using the USB floppy emulator, there is a way that i can configure the Floppy emulator similar to the parameters that worked with the SD emulator?

Which USB floppy emulator ? The USB HxC Floppy Emulator or someting else ?

[koh81]

The USB HxC Floppy Emulator the one that I bought from www.lotharek.pl

[Jeff]

The USB HxC Floppy Emulator the one that I bought from http://www.lotharek.pl

Ok, just change the setting into the "USB HxC Floppy Emulator" settings window in the hxc software.
But one to keep in mind : The USB HxC Floppy Emulator is an old design and doesn't have the write support.

[koh81]

ok I just need the emulator to read, what settings do I need to apply to the USB HxC Floppy Emulator software window? So it can work similar to the sd Hxc emulator, from I have been reading, I know that the emulation type has to be sugart, the drive Id settings I get from the physical drive of the machine? and the packet size setting what should be? thanks in advance for the help.