SD CARD VERSION HAVE NO MASSAGE ON LCD

sixty_cel · Post by **sixty_cel** » Sun Nov 22, 2009 3:45 pm

Hi Every body

I made Stand Alone version But first problem after operate

no have massage on my display please someone help me.

emrez · Post by **emrez** » Sun Nov 22, 2009 5:01 pm

Hello,
LCD pin 3. connected to the 10k ?
Did You install the bootloader and upd ?
What is the status rd3 led.
Regards.

sixty_cel · Post by **sixty_cel** » Sun Nov 22, 2009 6:44 pm

The resault is

-Led 3 is blink blink 1 time and 3 seconds pause cycle

Why no have massage in LCD if I'm not choose SD inti the slot.

emrez · Post by **emrez** » Sun Nov 22, 2009 7:08 pm

* Copy the new firmware file (HXCFE*.upd) to a freshly formated FAT32 SDCard.
* Insert the SDCard into the emulator
* Press Up and Down buttons before power up and keep it pressed at least 1 seconds at power up.
* Wait some seconds .... its done !

-- the lcd does not display in the firmware upd
information you can not do, I sends full hex.

Making (step by step video) coming soon

Best regards.

sixty_cel · Post by **sixty_cel** » Sun Nov 22, 2009 10:12 pm

emrez

Thank you so much for compile file.

Now I an see letter in LCD YEH YEH YEH.

sixty_cel · Post by **sixty_cel** » Tue Nov 24, 2009 5:08 pm

Hi Jeff

I'm try for several time.

the resault

-insert sd-card

-push up and down switch

-open power supply

-Led 3 Blink 4 times and pause 3 second

Regards

Post by **Jeff** » Tue Nov 24, 2009 5:17 pm

sixty_cel wrote:Hi Jeff

I'm try for several time.

the resault

-insert sd-card

-push up and down switch

-open power supply

-Led 3 Blink 4 times and pause 3 second

Regards

reflash your pic with the latest bootstrap, and use a freshly formated sdcard.

sixty_cel · Post by **sixty_cel** » Tue Nov 24, 2009 5:19 pm

In Sd-card version in one-page of LCD can only have 1 file that convert from raw file .

Am I right under stand?

MS-Dos bootable is an hiden file how to fill in sd-card.

Regards

My Name Bird

sixty_cel · Post by **sixty_cel** » Tue Nov 24, 2009 5:25 pm

If I want to fill more than one file in to one page of SD-card Can I do this condition?

The memory in usb type is 32 K/B.

Can I add the size of ram.

Or why the file is .hfe?

Regards

Bird

sixty_cel · Post by **sixty_cel** » Wed Nov 25, 2009 12:53 am

Hi Jeff

Now I can operate the board.

i connect to PC but some file windows mesage

-the disk not format

-or some file please insert disk into drive a:

I think some mistake about raw file format configuration page

how to set config to test with pc.

regards

Post by **Jeff** » Wed Nov 25, 2009 12:55 am

sixty_cel wrote:Hi Jeff

Now I can operate the board.

i connect to PC but some file windows mesage

-the disk not format

-or some file please insert disk into drive a:

I think some mistake about raw file format configuration page

how to set config to test with pc.

regards

what do you want test ? an *.img file ? or an new floppy image ?
don't forget to put a jumper in the right position.

sixty_cel · Post by **sixty_cel** » Wed Nov 25, 2009 2:57 am

Hi Jeff

Now I can operate EMU all condition .

I think It is a wonderful project.

If I want to product to sell how I do.

Only in my country.

Jman · Post by **Jman** » Mon Feb 22, 2010 2:52 am

I had same problem... thought my LCD was incompatible (TOPWAY LMB162ABC) but then I found the backlight pot.

In the words of Homer Simpson... DOH!